-
According to the operation mode, can be divided into:manual winding machine,semi automatic winding machine,automatic winding machine.Lithium battery winding machineand the capacitor winding machine, buyers usually according to classification of origin, mainly divided into: domestic winding machine, winding machine, South Korea Japan winding machine. Battery manufacturers generally small scale will...
read more
-
We have some large factories that we more or less have seen roller press. But surely everyone for roller press is not so understanding. Here I am for everyone detail our company’s flagship product roll press. Roller press and a series of broken classifier as a pre-grinding system with open cement mill roll grinding system consisting, in particular the process of using the system as a new and effic...
read more
-
The Electrode Coating Machine is the key equipment for the production of lithium battery electrode. Because it directly affects the subsequent rolling operation, and even affects the performance of the entire battery. At present, the mainly lithium battery electrode coating process is: scraper type, roll to roll transfer coating type and a slit extrusion type. General speaking, laboratory equ...
read more
-
Electrode Preparation is a key part in the whole battery manufacturing process, the quality of electrode directly affects the next step. The battery slurry preparation is a non - Newtonian high viscosity fluid which is formed by mixing the active materials, binders, solvents and other powders evenly. This slurry requires a certain viscosity, good fluidity and a sufficiently small particle size. So...
read more
-
As the core product of replacing the fuel - powered vehicle, new energy vehicle has been accepted by more and more users. Similarly, as one of the components of new energy vehicles, power battery has a more and more promising market. As a high-tech enterprise in the field of lithium-ion battery and supercapacitor, TOB has always been committed to the development of the fuel cells, TOB New Energy c...
read more
-
When preparing the electrode of lithium ion battery, aluminum foil is used as the cathode current collector foil, while copper foil is used as the anode current collector foil. If a single smooth foil is used, it is recommended to apply the foil on the rough side to increase the bonding force between the current collector foil and the materials. There is no special requirement for the thickness of...
read more
-
After electrode coating, electrode through drying process in oven and the coated electrode becomes loose. If used directly, the cathode material and anode material is easy to fall off and damage after being soaked by electrolyte. The electrode can be pressed by the battery electrode roller machine. The stability, firmness and electrochemical properties of the pressed electrode were improved, and t...
read more
-
Before starting, place the prepared button battery assembly parts and materials in the glove box. We can offer a full set of coin cell parts and materials, including coin cell case, coated electrode, cathode and anode materials, electrolyte, coin cell spacer, wave spring, belleville washers, battery separator. 1. Place the spacer and the cathode electrode into the coin cell cathode case one by one...
read more
-
One-Step Pressing, it is rolling only once to achieve the designed thickness and density of the battery electrode. Two-Step Pressing, it is rolling the battery electrode to a certain thickness (such as 90μm) at first time, and achieve the designed thickness (such as 70μm) and desired density through the second time pressing. The main purpose of the rolling press is to control the electrode in the ...
read more
-
Battery Electrode Transfer Roll Coating Machine Coating roller rotation drive slurry, through adjusting the scraper clearance to adjust the amount of slurry transfer, the slurry is transferred to the substrate(copper foil,aluminum foil, etc.) by the rotation of the coating roller, and according to the process requirements, control the coating thickness to meet the weight requirements. At the same ...
read more
-
The function of formation, The internal anode and cathode materials are activated by charging and discharging, and a good SEI film is formed on the surface of the anode. The principle of formation, The formation of lithium cell is the initialization of the battery, which activates the active material of the cell, which is a process of energy conversion. The formation of lithium cell is a complex p...
read more
-
The process of 18650 lithium battery pack is mainly based on the structure of pack battery, and most of the 18650 lithium battery pack process features are similar. The distinctive features of the 18650 lithium battery PACK process are multiple parallel and multiple series. The greatest feature of the 18650 lithium battery Pack is its flexible combination, most of which can be semi-automated. TOB ...
read more
-
The first is to confirm and bake the battery material. Generally, the battery conductive agent needs to be baked at 120℃ for 8 hours. The PVDF powder should be baked at 80℃ for 8 hours. The cathode active material (LFP, NCM, etc.) depends on the state and process of incoming material whether it needs to be baked and dried. After drying, (wet process) Mixing the PVDF powder and NMP solvent to make ...
read more
-
The cathode electrode coating is the cathode slurry extrusion coating or spraying on the cathode current collector aluminum foil, the density of one side is 20 to 40 mg/cm2. Coating oven temperature conventional 4-8 sections (or more), each section of baking temperature 95℃ ~ 120℃ according to the actual needs to adjust, to avoid baking cracking transverse cracks and solvent phenomenon, the speed ...
read more
-
Drying the battery cathode electrode after battery coating process, it is necessary to roll the coated battery electrode foil during the process time. The electrode rolling process is to compacting the coated electrode, at present there are hot pressing and cold pressing two processes of battery electrode rolling press. Battery electrode hot press compaction rate is higher than cold press, and the...
read more
-
After the slitting process, the cathode and anode electrode piece should be dried (cathode 120℃, anode 105-110℃). Then is the battery tab welding and high temperature adhesive taping process. The length of the battery tabs and the shaping width need to be taken into account. Take the 18650 battery as an example, The design of the battery cathode tabs exposure mainly takes into account the reasonab...
read more
-
Battery electrode winding is the separator, cathode sheet, anode sheet through the battery electrode winding machine into a single battery cells. TOB New Energy can provide the battery winding machine for 18650 lithium-ion cylindrical cell precision winding for 18650 production line. The principle of battery winding is to use the anode to cover the cathode, and then through the battery separator t...
read more
-
Insert the welding needle (usually made of copper or alloy) into the middle hole of the rolled battery cells. The specifications of commonly used welding needles are Φ2.5*1.6mm,It is qualified to reach welding strength of anode electrode tab ≥12N, low strength can lead to the unstable welding and larger internal resistance. If the welding strength is too high, it is easy to destroy the nickel laye...
read more
-
After the battery cells drying process, the battery cell will be tested for moisture and meet the standard before proceeding to the next step of battery electrolyte filling process（cylindrical cell）. Put the roasted battery cell into the vacuum glove box quickly, weigh it and record the weight, place the injection cup on the upper side of the battery and add the electrolyte into the cup. If not su...
read more
-
Take the laboratory scale battery caps welding machine as an example, Put the battery caps and battery spot welder in the glove box in advance, place the battery caps on the mold of the battery spot welder, hold the battery cells on the other hand, align the cathode battery tabs of the battery cell with the caps, after confirming the spot welding position is correct, depress the foot pedal. After ...
read more
中文
français
Deutsch
italiano
español
português
Nederlands
日本語
한국의
subscribe to us 
