-
For lithium ion batteries, the cathode materials that can be used should meet the characteristics of large reversible capacity, high potential and stability, non-toxic and low production cost. At present, lithium iron phosphate is the most common cathode material for lithium ion batteries. However, LiFePO4 has poor electrical conductivity and low lithium ion mobility. If LiFePO4 material is combin...
read more
-
Graphene Oxide is a two-dimensional planar nanomaterial composed of carbon atoms with a hexagonal honeycomb lattice，the c-c bond length is 0.141nm, the theoretical density is about 0.77mg/m2, and the thickness is only about the diameter of a carbon atom. Carbon atoms participate in hybridization in the way of sp2, and electrons can smoothly conduct between layers, so graphene conducts electricity ...
read more
-
Introduction: Polyvinylidene fluoride binder(PVDF) is currently the most commonly used oil binder in the lithium ion battery industry. It is a non-polar chain polymer binder. It is characterized by strong oxidation resistance, good thermal stability and easy dispersion. N-methylpyrrolidone (NMP) is required as a solvent. This solvent has a high volatilization temperature, has a certain environment...
read more
-
The lithium-rich manganese-based (xLi[Li1/3-Mn2/3]O2; (1–x) LiMO2, M is a transition metal 0≤x≤1, and the structure is similar to LiCoO2) has a high discharge specific capacity. It is about twice the actual capacity of the cathode material currently used, and is therefore widely studied for lithium battery materials. In addition, since the material contains a large amount of Mn element, it is more...
read more
-
A good combination can not only improve cell utilization, but also control monomer consistency, which is the basis of achieving good discharge capacity and cycle stability. However, the dispersion degree of ac impedance of single battery capacity will be intensified, which will weaken the cycling performance and available capacity of battery. But how do you achieve good grouping of battery? Quanti...
read more
-
Lithium ion battery is a kind of energy storage device, currently the commonly used lithium ion battery according to the cathode material can be divided into iron phosphate lithium battery, ternary battery and manganese acid lithium battery. Take the lithium iron phosphate battery as an example: when discharging, the iron phosphate in the positive electrode and the lithium ion transferred from the...
read more
-
As the core product of replacing the fuel - powered vehicle, new energy vehicle has been accepted by more and more users. Similarly, as one of the components of new energy vehicles, power battery has a more and more promising market. As a high-tech enterprise in the field of lithium-ion battery and supercapacitor, TOB has always been committed to the development of the fuel cells, TOB New Energy c...
read more
-
There are many kinds of cathode materials for lithium ion batteries. According to the difference of cathode materials, they can be divided into LiNiMnCoO2 NMC(NCM) cathode material, LiNiCoAlO2 NCA cathode material, LiFePO4 LFP cathode, LiCoO2 LCO cathode, LiMn2O4 LMO cathode and Li4Ti5O12 LTO material. Ternary lithium battery refers to the lithium battery that uses three transition metal oxides ni...
read more
-
The first is to confirm and bake the battery material. Generally, the battery conductive agent needs to be baked at 120℃ for 8 hours. The PVDF powder should be baked at 80℃ for 8 hours. The cathode active material (LFP, NCM, etc.) depends on the state and process of incoming material whether it needs to be baked and dried. After drying, (wet process) Mixing the PVDF powder and NMP solvent to make ...
read more
-
The anode of lithium battery is composed of anode active materials, conductive agent, battery binder and dispersant. The conventional anode electrode system is a water mixing process (the solvent is deionized water), so the incoming material does not require drying. This process requires: Conductivity of deionized water ≤1us/cm. Workshop temperature ≤40℃, Humidity :≤25%RH. After confirmation of th...
read more
-
Hi-pot test voltage of 200 ~ 500V is required before the battery cell is put into the battery stainless steel case(Test for high voltage short circuit) and vacuuming processing(Control dust further before loading the battery cells). We can provide the most professional lithium battery cells short circuit tester. Moisture, burr and dust are the three control points of lithium battery manufacturing,...
read more
-
After the battery cells of the cylindrical battery passes through the rolling groove by battery grooving machine, the next step is very important: drying the battery cells. Battery cell in the production process will bring a certain amount of water, if not timely removal of water, control it within the standard value range, which will seriously affect the battery performance and safety performance...
read more
-
Vacuum drying is to place the materials to be dried in a closed space, and use vacuum equipment to lower the air pressure in the closed space to an atmospheric pressure, while continuously heating the materials, so that the water molecules in the materials gradually diffuse to the surface of the materials due to the effect of pressure difference and concentration difference, and after the material...
read more
-
The packaging method of lithium battery depends on the shell material it uses. In general, only lithium pouch batteries will use aluminum laminate film and heat sealing. The metal cans batteries are usually sealed by laser welding. Aluminum laminate film generally has three layers, respectively nylon layer, Al layer, PP layer. Nylon layer is to ensure the appearance of aluminum laminate film,...
read more
-
The theoretical basis and battery structure of sodium ion battery (Na-ion batteries) and lithium ion battery are very similar. Liquid sodium-ion batteries (like solid-state lithium-ion batteries, are also being investigated) are composed of positive electrode, negative electrode, current collector, electrolyte, and battery separator. Among them, electrolyte and separator basically follow the...
read more
-
Materials Material selection is the first factor affecting the performance of lithium-ion batteries. If you choose the battery material with poor cycle performance, even if the process is reasonable and the production is perfect, the cycle of the cell can not be guaranteed. And with better materials, the cycle performance may not be too bad even if there are some problems in the subsequent product...
read more
-
Prussian Blue Cathode Materials for Aqueous Sodium-ion Batteries: Preparation and Electrochemical Performance Author：LI Yong. Prussian Blue Cathode Materials for Aqueous Sodium-ion Batteries: Preparation and Electrochemical Performance. Journal of Inorganic Materials[J], 2019, 34(4): 365-372 doi:10.15541/jim20180272 TOB New Energy can provide a full set of battery material and batte...
read more
-
Enhanced Lithium Storage Stability Mechanism of Ultra-high Nickel LiNi0.91Co0.06Al0.03O2@Ca3(PO4)2 Cathode Materials Author：ZHU Hezhen, WANG Xuanpeng, HAN Kang, YANG Chen, WAN Ruizhe, WU Liming, MAI Liqiang. Enhanced Lithium Storage Stability Mechanism of Ultra-high Nickel LiNi0.91Co0.06Al0.03O2@Ca3(PO4)2 Cathode Materials. Journal of Inorganic Materials, 2022, 37(9): 1030-1036...
read more
-
The battery slurry is a highly viscous solid-liquid two-phase suspension system, and to assess the stability of this system, the first step is to study its composition and its functional properties. Most of the lithium industry uses oil-based slurry, which is a mixture formed by mixing and dispersing active materials, binders, conductive agents, solvents, etc. in a certain ratio and order. Cathode...
read more
-
The Preparation Method of Battery Cathode Slurry Wet Electrode Preparation Process A double planetary mixer was used as the cathode electrode slurry preparation equipment. First, prepare polyvinylidene fluoride (PVDF) glue. Use an ordinary mixing tank to pour a certain amount of solvent NMP (N-methylpyrrolidone) first, add the binder PVDF powder according to the designed solid content, and stir fo...
read more
中文
français
Deutsch
italiano
español
português
Nederlands
日本語
한국의
subscribe to us 
