Electrolyte

Although high-voltage lithium battery materials are getting more and more attention, these high-voltage anode materials are still unable to achieve good results in practical production and application. The biggest limiting factor is that the electrochemical stability window of the carbonate-based electrolyte is low. When the battery voltage reaches about 4．5（vs．Li/Li＋）, the electrolyte begins to p...

Lithium Chip Metal lithium chip used in the laboratory can provide a far greater source of lithium, Lithium chip shall have less impurities and the size shall be larger than that of the electrode to be measured, and the purity of lithium chip shall not be less than 99.9%. General requirements for lithium chip in the preparation of coin cell: diameter 15 ~ 15.8mm (the corresponding electrode size i...

After the battery cells drying process, the battery cell will be tested for moisture and meet the standard before proceeding to the next step of battery electrolyte filling process（cylindrical cell）. Put the roasted battery cell into the vacuum glove box quickly, weigh it and record the weight, place the injection cup on the upper side of the battery and add the electrolyte into the cup. If not su...

After pouch cells top sealing and side sealing, need to do X-ray to check the alignment of the battery cells, then put the battery cells into the drying room for drying(you can also use the drying oven to drying the battery cells). After the battery cells drying process is completed, The next step is electrolyte filling process and primary sealing process. Through the introduction of the previous ...

MOF/Poly(Ethylene Oxide) Composite Polymer Electrolyte for Solid-state Lithium Battery LIANG Fengqing, WEN Zhaoyin 1. CAS Key Laboratory of Materials for Energy Conversion, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050, China 2. Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China Abstract Solid...

Dual-lithium-salt Gel Complex Electrolyte: Preparation and Application in Lithium-metal Battery GUO Yuxiang, HUANG Liqiang, WANG Gang, WANG Hongzhi. Dual-lithium-salt Gel Complex Electrolyte: Preparation and Application in Lithium-metal Battery. Journal of Inorganic Materials, 2023, 38(7): 785-792 DOI:10.15541/jim20220761 Abstract Metallic Li is one of the ideal anodes for high energy de...

Na3Zr2Si2PO12 Ceramic Electrolytes for Na-ion Battery: Preparation Using Spray-drying Method and Its Property Author：LI Wenkai, ZHAO Ning, BI Zhijie, GUO Xiangxin. Na3Zr2Si2PO12 Ceramic Electrolytes for Na-ion Battery: Preparation Using Spray-drying Method and Its Property. Journal of Inorganic Materials, 2022, 37(2): 189-196 DOI:10.15541/jim20210486 Abstract Na-ion batteries, ...

Author: XIA Qiuying, SUN Shuo, ZAN Feng, XU Jing, XIA Hui School of Materials Science and Engineering, Nanjing University of Science and Technology, Nanjing 210094, China Abstract All-solid-state thin film lithium battery (TFLB) is regarded as the ideal power source for microelectronic devices. However, the relatively low ionic conductivity of amorphous solid-state electrolyte ...

Why are all-solid-state batteries an industry trend? High security: The safety issues of liquid batteries have always been criticized. The electrolyte is easily flammable under high temperature or severe impact. Under high current, lithium dendrites will also appear to pierce the separator and cause short circuit. Sometimes the electrolyte may undergo side reactions or decompose at high temperatur...

The dew point is the temperature at which moisture condenses. When the water vapor content in the air remains unchanged and the air pressure is kept constant, the temperature at which the air is cooled to saturation is called the dew point temperature (Td), or dew point for short. It can also be understood as the temperature at which water vapor and water reach equilibrium. The difference between ...